Robofun 機器人論壇

標題: arduino 加速度感測器 gy50 L3G4200 詢問 [打印本頁]

作者: yasd468520 時間: 2019-8-21 13:37
標題: arduino 加速度感測器 gy50 L3G4200 詢問
程式碼打好了可是序列埠監控視窗顯示的 X值 Y值 Z值感測器不管怎麼動都顯示-1
對於程式我不是很厲害我是參考別人的數值下去改
但始終找不出原因..
只好上來找大神來幫助

#include <Wire.h>
#include <L3G.h>
#define  CTRL_REG1 0x20
#define  CTRL_REG2 0x21
#define  CTRL_REG3 0x22
#define  CTRL_REG4 0x23
#define  CTRL_REG5 0x24

int L3G4200D_Address = 105;

int x;
int y;
int z;

void setup(){
  Wire.begin();
  Serial.begin(9600);

  Serial.println("starting up L3G4200D");
  setupL3G4200D(2000);
  delay(1500);
}

void loop(){
  getGyroValues();

  Serial.print("X:");
  Serial.print(x);
  Serial.print(" , ");

  Serial.print("Y:");
  Serial.print(y);
  Serial.print(" , ");

  Serial.print("Z:");
  Serial.println(z);

  delay(100);

}

void getGyroValues(){
  byte xMSB = readRegister(L3G4200D_Address, 0x29);
  byte xLSB = readRegister(L3G4200D_Address, 0x28);
  x = ((xMSB << 8) | xLSB);

  byte yMSB = readRegister(L3G4200D_Address, 0x2B);
  byte yLSB = readRegister(L3G4200D_Address, 0x2A);
  y = ((yMSB << 8) | yLSB);

  byte zMSB = readRegister(L3G4200D_Address, 0x2D);
  byte zLSB = readRegister(L3G4200D_Address, 0x2C);
  z = ((zMSB << 8) | zLSB);
}

int setupL3G4200D(int scale){
  writeRegister(L3G4200D_Address, CTRL_REG1, 0b00001111);

  writeRegister(L3G4200D_Address, CTRL_REG2, 0b00000000);

  writeRegister(L3G4200D_Address, CTRL_REG3, 0b00001000);

  if(scale == 250){
writeRegister(L3G4200D_Address, CTRL_REG4, 0b00000000);
  }else if(scale == 500){
writeRegister(L3G4200D_Address, CTRL_REG4, 0b00010000);
  }else{
writeRegister(L3G4200D_Address, CTRL_REG4, 0b00110000);
  }
  writeRegister(L3G4200D_Address, CTRL_REG5, 0b00000000);
}

void writeRegister(int deviceAddress, byte address, byte val){
  Wire.beginTransmission(deviceAddress);
  Wire.write(address);
  Wire.write(val);
  Wire.endTransmission();
}

int readRegister(int deviceAddress, byte address){
  int V;
  Wire.beginTransmission(deviceAddress);
  Wire.write(address);
  Wire.endTransmission();

  Wire.requestFrom(deviceAddress,1);

  while(Wire.available()){
  }
V = Wire.read();
return V;
  }

擷取.PNG (13.44 KB, 下載次數: 235)

歡迎光臨 Robofun 機器人論壇 (https://robofun.net/forum/)