|
|
2#
樓主 |
發表於 2006-8-16 13:21:31
|
只看該作者
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
;********************************************************
;
; Stepper Motor controller
;
; Author : Seiichi Inoue
;********************************************************
list p=pic16f84a
include p16f84a.inc
__config _hs_osc & _wdt_off & _pwrte_on & _cp_off
;**************** Label Definition ********************
cblock h'0c'
mode ;Operation mode
;0=stop 1=right 2=left
count1 ;Wait counter
count2 ;Wait counter(for 1msec)
endc
rb0 equ 0 ;RB0 of PORTB
rb1 equ 1 ;RB1 of PORTB
rb2 equ 2 ;RB2 of PORTB
rb5 equ 5 ;RB5 of PORTB
rb7 equ 7 ;RB7 of PORTB
;**************** Program Start ***********************
org 0 ;Reset Vector
goto init
org 4 ;Interrupt Vector
clrf intcon ;Clear Interruption reg
;**************** Initial Process *********************
init
bsf status,rp0 ;Change to Bank1
clrf trisa ;Set PORTA all OUT
movlw b'00100111' ;RB0,1,2.5=IN RB7=OUT
movwf trisb ;Set PORTB
movlw b'10000000' ;RBPU=1 Pull up not use
movwf option_reg ;Set OPTION_REG
bcf status,rp0 ;Change to Bank0
clrf mode ;Set mode = stop
clrf count1 ;Clear counter
clrf count2 ;Clear counter
movlw b'00000101' ;Set PORTA initial value
movwf porta ;Write PORTA
bsf portb,rb7 ;Set RB7 = 1
btfsc portb,rb5 ;RB5 = 0 ?
goto $-1 ;No. Wait
start
;************* Check switch condition *****************
btfsc portb,rb1 ;RB1(stop key) = ON ?
goto check1 ;No. Next
clrf mode ;Yes. Set stop mode
goto drive ;No. Jump to motor drive
check1
btfsc portb,rb2 ;RB2(right key) = ON ?
goto check2 ;No. Next
movlw d'1' ;Yes. Set right mode
movwf mode ;Save mode
goto drive ;No. Jump to motor drive
check2
btfsc portb,rb0 ;RB0(left key) = ON ?
goto drive ;No. Jump to motor drive
movlw d'2' ;Yes. Set left mode
movwf mode ;Save mode
;******************** Motor drive *********************
drive
movf mode,w ;Read mode
bz start ;mode = stop
bsf portb,rb7 ;Set RB7 = 1
btfsc portb,rb5 ;RB5 = 0 ?
goto $-1 ;No. Wait
movlw d'5' ;Set loop count(5msec)
movwf count1 ;Save loop count
loop call timer ;Wait 1msec
decfsz count1,f ;count - 1 = 0 ?
goto loop ;No. Continue
bcf portb,rb7 ;Set RB7 = 0
btfss portb,rb5 ;RB5 = 1 ?
goto $-1 ;No. Wait
movf porta,w ;Read PORTA
sublw b'000000101' ;Check motor position
bnz drive2 ;Unmatch
movf mode,w ;Read mode
sublw d'1' ;Right ?
bz drive1 ;Yes. Right
movlw b'00001001' ;No. Set Left data
goto drive_end ;Jump to PORTA write
drive1
movlw b'00000110' ;Set Right data
goto drive_end ;Jump to PORTA write
;-------
drive2
movf porta,w ;Read PORTA
sublw b'000000110' ;Check motor position
bnz drive4 ;Unmatch
movf mode,w ;Read mode
sublw d'1' ;Right ?
bz drive3 ;Yes. Right
movlw b'00000101' ;No. Set Left data
goto drive_end ;Jump to PORTA write
drive3
movlw b'00001010' ;Set Right data
goto drive_end ;Jump to PORTA write
;-------
drive4
movf porta,w ;Read PORTA
sublw b'000001010' ;Check motor position
bnz drive6 ;Unmatch
movf mode,w ;Read mode
sublw d'1' ;Right ?
bz drive5 ;Yes. Right
movlw b'00000110' ;No. Set Left data
goto drive_end ;Jump to PORTA write
drive5
movlw b'00001001' ;Set Right data
goto drive_end ;Jump to PORTA write
;-------
drive6
movf porta,w ;Read PORTA
sublw b'000001001' ;Check motor position
bnz drive8 ;Unmatch
movf mode,w ;Read mode
sublw d'1' ;Right ?
bz drive7 ;Yes. Right
movlw b'00001010' ;No. Set Left data
goto drive_end ;Jump to PORTA write
drive7
movlw b'00000101' ;Set Right data
goto drive_end ;Jump to PORTA write
;-------
drive8
movlw b'00000101' ;Compulsion setting
drive_end
movwf porta ;Write PORTA
goto start ;Jump to start
;************* 1msec Timer Subroutine *****************
timer
movlw d'200' ;Set loop count
movwf count2 ;Save loop count
tmlp nop ;Time adjust
nop ;Time adjust
decfsz count2,f ;count - 1 = 0 ?
goto tmlp ;No. Continue
return ;Yes. Count end
;********************************************************
; END of Stepper Motor controller
;********************************************************
end
http://www.interq.or.jp/japan/se-inoue/e_step7.htm |
|
發表於 2006-8-16 13:16:05
收藏
分享